Comtech EF Data KPA-040 Specifikace Strana 116
- Strana / 128
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
KPA Ku-Band Indoor Solid-State Power Amplifier Revision 1
Appendix C MN/KPA.IOM
C–20
C.7.2 Old Configuration Commands
Amplifier On/OFF Amplifier Control:
Confirmation:
Retrieve AMP Status:
Confirmation:
<DEV/AMP_xxx'cr'
>DEV/AMP_xxx'cr''lf']
<DEV/AMP_'cr'
>DEV/AMP_xxx'cr''lf']
Where: xxx = On or Off
The default is On.
The Comtech EF Data KPA provides the user direct control of the
9VDC supply voltage to the solid-state RF power FETs. This
feature provides the ability to put the KPA into a low power
consumption mode when the unit is offline.
Mute Mute Output:
Confirmation:
Retrieve Mute Status:
Confirmation:
<DEV/MUT_xxx'cr'
>DEV/MUT_xxx'cr''lf']
<DEV/MUT_'cr'
>DEV/MUT_xxx'cr''lf']
Where: xxx = On or Off
The default is On.
The user is provider output mute control via the remote interface
using this command.
Attenuator Set Attenuator:
Confirmation:
Retrieve Attenuator:
Confirmation:
<DEV/ATT_yy.yy'cr'
>DEV/ATT_yy.yy'cr''lf']
<DEV/ATT_'cr'
>DEV/ATT_yy.yy'cr''lf']
Where: yy.yy = 0.0 to 20.0 dB in 0.25 steps.
The default is 10 dB.
Auto Fault Recovery Set Fault Recovery:
Confirmation:
Retrieve Status:
Confirmation:
<DEV/AFR_xxx'cr'
>DEV/AFR_xxx'cr''lf']
<DEV/AFR_xxx'cr'
>DEV/AFR_xxx'cr''lf']
Where xxx = On or Off
The default is Off.
The KPA output automatically muted in the event of a detected
fault. Auto Fault Recovery, if enabled, will cause the output signal to
go active (unmuted) if all faults clear. If disabled, the output will
remain muted even after all faults clear until a MUT_OFF command
is received.
- Errata A 3
- Part Number MN/KPA.IOM 5
- Revision 1 5
- October 29, 2010 5
- Table of Contents 7
- Figures 11
- PREFACE 13
- Conventions and References 14
- Metric Conversion 14
- Trademarks 14
- Cautions and Warnings 14
- IMPORTANT 15
- Warranty Policy 16
- Limitations of Warranty 16
- Exclusive Remedies 17
- Customer Support 18
- Online Customer Support 18
- Chapter 1. INTRODUCTION 19
- 1.2 Functional Description 20
- Introduction MN/KPA.IOM 21
- 1.3 KPA Specifications 23
- 1.3.5 Dimensional Envelopes 27
- Chapter 2. INSTALLATION 29
- 2.2 Rack Mounting the KPA 30
- Installation MN/KPA.IOM 31
- Chapter 3. CONNECTORS AND 33
- PINOUTS 33
- 3.2 RF Connections 35
- 3.2.2 J2 RF OUT Connector 35
- 3.3 Utility Connections 36
- 3.3.7 J6 COM 1 Connector 39
- Chapter 4. FLASH UPGRADING 41
- Flash Upgrading MN/KPA.IOM 42
- Chapter 5. FRONT PANEL 45
- OPERATION 45
- 5.1.1 Startup Checklist 46
- 5.1.2 LED Indicators 46
- 5.1.3 Keypad 47
- 5.1.4 Front Panel Display 48
- 5.2 Opening Screen 48
- 5.3 SELECT: (Main) Menu 49
- ◄ ► arrows keys, then press 50
- 5.3.1.2 CONFIG: Amp 54
- 5.3.2 SELECT: Monitor 57
- 5.3.2.1 MONITOR: Faults 58
- 5.3.2.2 MONITOR: Stored 58
- 5.3.3.1 UTILITY: Date/Time 60
- 5.3.3.3 UTILITY: PowerMon 60
- 5.3.3.4 UTILITY: Firmware 61
- 5.3.3.5 UTILITY: RefOsc 61
- 5.3.4 SELECT: Front Panel 62
- Chapter 6. KPA ETHERNET 63
- MANAGEMENT 63
- 6.4 Telnet Interface 65
- 6.5.3 Web Server Menu Tree 67
- 6.5.4.1 Home pages 68
- 6.5.4.2 Admin pages 70
- 6.5.4.2.2 Admin 72
- Amplifier 73
- Alarm Mask 74
- [Change Offsets] as 75
- Redundancy Mode 77
- 6.5.4.4 Status pages 78
- Appendix A. MAINTENANCE AND 81
- TROUBLESHOOTING 81
- A.2 Maintenance Testing 82
- A.2.1 Test Point Samples 82
- A.3 Troubleshooting 82
- A.3.1 Troubleshooting Guide 83
- Appendix A MN/KPA.IOM 84
- Appendix B. KPA REDUNDANT 87
- OPERATIONS 87
- Waveguide 88
- Appendix B MN/KPA.IOM 89
- 0.00 dBm 95
- -1.75 dB 95
- +1.75 dB 96
- Appendix C. REMOTE CONTROL 97
- C.3 EIA-232 98
- C.4 Basic Protocol 98
- C.5 Packet Structure 99
- C.5.1 Start of Packet 99
- C.5.2 Target Address 100
- C.5.3 Address Delimiter 100
- C.5.4 Instruction Code 100
- C.5.7 End of Packet 102
- Appendix C MN/KPA.IOM 103
- C–7 103
- C–8 104
- C–9 105
- C–10 106
- C–11 107
- C–12 108
- C–13 109
- C–14 110
- C–15 111
- C–16 112
- C–17 113
- C.7.1 Old Utility Commands 114
- C–19 115
- C–20 116
- C–21 117
- C.7.4 Old Status Commands 118
- C–23 119
- C–24 120
- C–25 121
- C–26 122
- C–27 123
- C.7.5 Old Stored Alarms 124
- C.7.6 Error Processing 125
- C.7.7 Configuration Errors 125
- C.7.8 Time-Outs 125
- C–30 126
- METRIC CONVERSIONS 127
- Units of Length 127
- Temperature Conversions 127
- Units of Weight 127
- 480 • 333 • 2200 PHONE 128
- • 333 • 2161 FAX 128
Související produkty a manuály pro Audio zesilovače Comtech EF Data KPA-040
Audio zesilovače Comtech EF Data LPOD Specifikace
(218 stránky)
(218 stránky)
Audio zesilovače Comtech EF Data LPOD Specifikace
(60 stránky)
(60 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce