Comtech EF Data LPOD Specifikace Strana 115
- Strana / 218
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
LPOD C-, X-, or Ku-Band Outdoor Amplifier / Block Up Converter (BUC) MN-LPOD
Serial-based Remote Product Management Revision 10
5–15
Parameter Type
Command
(Instruction
Code and
Qualifier)
Arguments
for Command
or Response
to Query
Description of Arguments
(Note that all arguments are printable ASCII characters)
Response to
Command
(Target to
Controller)
Query
(Instruction
Code and
Qualifier)
Response to Query
(Target to
Controller)
Calibrate LNB
Current
CLC=
none
Command or Query.
Sets or returns, as a reference point, the value of the LNB Current Supply (in mA) in the form xxx.x.
Default value: 000.0
The LNB current alarm point is then determined by the calibrated LNB reference point, and the LNB current window
setting (see LCW command).
Note: this command will return a mode error if the LNB current source output has not been enabled first (see
LCS command).
Example: <1/CLC=’cr’
>0001/CLC=’cr’’lf’
The CLC query will return the value that was stored during the LNB current calibration.
Example: <1/CLC?’cr’
>0001/CLC=xxx.x where xxx.x is the calibrated LNB current value in mA.
CLC=
CLC?
CLC*
CLC?
CLC=xxx.x
(See Description of
Arguments)
Clear Statistics
Log
CSL=
1 byte
Command only.
Clears the statistics log entries. This command takes no arguments.
Example:
<1/CSL=1’cr’
>0001/CSL=’cr’’lf’
CSL=
CSL?
CSL*
N/A
CSL=
Concise Utility
Status
E
N/A
15 bytes
Query only.
Returns the Maintenance status of the unit, response is semicolon delimited, in the form aaaa;bbbbb;ccc where:
aaaa = Remote Unit Address
bbbbb = Remote Baud Rate
ccc = Reference oscillator tuning voltage DAC value (see Note)
Note: ccc is only present if a reference oscillator is installed.
Example:
<1/CUS?’cr’
>0001/CUS=aaaa;bbbbb;ccc;’cr’’lf’
CUS=
CUS?
CUS=x….x
(See Description of
Arguments)
- Revision 10 1
- Part Number MN-LPOD 3
- Revision 10 3
- TABLE OF CONTENTS 5
- vii 9
- FIGURES 10
- PREFACE 13
- Electrical Safety Notice 14
- Product Support 15
- Preface Revision 10 16
- Chapter 1. INTRODUCTION 19
- 1.2 Functional Description 20
- 1.3 Features 20
- 1.3.7 Optional LNB Support 21
- 1.4 Theory of Operation 22
- 1.4.1 SSPA Block Diagrams 22
- 1.4.2 SSPA Module 23
- 1.4.3 Cooling System 24
- 1.4.5 LNB Operation 24
- 1.4.6 Power Supply 24
- BUC C, Ku, X LO Frequencies 25
- 1.5.1 Characteristics 26
- 1.5.4 Environmental 28
- 1.5.5 Physical 28
- 1.6 Dimensional Envelopes 30
- Introduction Revision 10 31
- Chapter 2. SYSTEM 41
- CONNECTIONS, INSTALLATION 41
- STARTUP 41
- 2.3 Interface Connectors 44
- Control Port) 48
- 2.3.8 Ground Connector 49
- 2.5 Power-up the LPOD 50
- Chapter 3. UPDATING FIRMWARE 55
- Chapter 4. ETHERNET-BASED 65
- REMOTE PRODUCT 65
- 4.3 SNMP Interface 66
- 4.3.3 SNMP Traps 67
- 4.4 Telnet Interface 70
- Enter the LPOD’s 71
- 4.5.2 User Login 73
- 4.5.3.1 Menu Tree 74
- 4.5.3.2 Page Navigation 74
- 4.5.3.3 Page Sections 74
- 4.5.3.4 Action Buttons 75
- 4.5.3.5 Drop-down Lists 75
- 4.5.3.6 Text or Data Entry 75
- 4.5.4.1 Home Pages 76
- 4.5.4.1.1 Home 76
- 4.5.4.1.2 Home 77
- 4.5.4.1.3 Home 78
- 4.5.4.2 Admin Pages 79
- 4.5.4.2.1 Admin 79
- Webpage Timeout 80
- 4.5.4.2.2 Admin 81
- 4.5.4.3 Config Pages 82
- 4.5.4.3.2 Config 84
- 4.5.4.3.3 Config 85
- Redundancy 87
- Online Status 87
- Force Online 87
- 4.5.4.4 Status Pages 88
- 4.5.4.4.1 Status 88
- 4.5.4.4.2 Status 89
- 4.5.4.4.3 Status 90
- 4.5.4.4.4 Status 91
- Alarm Mask 92
- Statistics Configuration 94
- 4.5.4.4.6 Status 95
- Control Bar and Refresh Tab 96
- Temperature Graph 97
- Power Graph 97
- LNB Current Graph 98
- Amplifier Status Graph 98
- Mute State Graph 98
- Online Status Graph 99
- Minimum Fan Speed Graph 99
- MANAGEMENT 101
- 5.2.2 Attenuator Control 102
- 5.2.3 Mute Control 102
- 5.2.4 Faults 102
- 5.2.5 Power Detector 104
- 5.2.6 Some Common Commands 104
- 5.2.7 End-of-Life Commands 104
- 5.1.1 EIA-485 105
- 5.1.2 EIA-232 106
- 5.1.3 Basic Protocol 106
- 5.1.4 Packet Structure 106
- 5.1.4.1 Start of Packet 107
- 5.1.4.2 Target Address 107
- 5.1.4.3 Address Delimiter 107
- 5.1.4.4 Instruction Code 108
- 5.1.4.7 End of Packet 109
- Appendix A. 1:1 REDUNDANCY 137
- Appendix A Revision 10 138
- A.5.1 Common Kit Examples 146
- BLANK PAGE 151
- Appendix B. CABLE DRAWINGS 193
- B.2 Control and Data Cables 194
- Appendix B Revision 10 195
- B.3 RF Cables 202
- B.3.1 RF Cable (Type ‘N’) 203
- Appendix C. MAINTENANCE 205
- Appendix C Revision 10 206
- 212
- 480 • 333 • 2200 PHONE 218
- • 333 • 2161 FAX 218
Související produkty a manuály pro Audio zesilovače Comtech EF Data LPOD
Audio zesilovače Comtech EF Data LPOD Specifikace
(60 stránky)
(60 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce